GAS PRESSURE REGULATORS-STABILIZERS
Pressure regulators-stabilizer is a device designed for reduction, regulation and maintenance of the pressure (flow) of hydro carbonated gases, gaseous phases of liquefied gases, compressed air as well as other non-aggressive gases constant at the outlet within prescribed limits regardless of inlet pressure. Pressure regulators-stabilizers can operate without external power source.
FIELD OF APPLICATION:
Gas distributing plants, heating plants, gas reciprocating engine power plants, gas burners and other equivalent equipment and installations, which require reduction and maintenance of the constant value of gas flow rate pressure.
MAXIMUM OPERATING PRESSURE:
- up to 6 bar
DIAMETER NOMINAL:
DN 15÷150
HOUSING MATERIAL:
- aluminum;
- steel.
VERSIONS:
1. Standard version (DN 15÷150) - designed for reduction, regulation and maintenance of the gas pressure within prescribed limits.
2. Regulator with in-built safety relief valve (DN 15÷150) – designed for reduction, regulation and maintenance of the gas pressure within prescribed limits and has function of gas discharge to the atmosphere (gas path) in case if controlled pressure is exceeded.
3. Combined regulator both with safety shut-off (DN25÷100) – designed for regulation and maintenance of the gas pressure within prescribed limits, and also stops gas supply, when prescribed gas outlet pressure is exceeded.
4. Combined regulator, both with safety shut-off valve and safety relief valve – designed for regulation and maintenance of the gas pressure within prescribed limits; has function of gas discharge to the atmosphere (gas path) when controlled pressure is exceeded, and also stops gas supply, when prescribed gas outlet pressure is exceeded;
Combined regulators-stabilizers can be manufactured in following versions:
- with safety shut-off valve and safety relief valve in separate housings.
- with safety shut-off valve and in-built safety relief valve.
- with safety shut-off valve and safety relief valve in one housing (monoblock unit version).
- combined household regulator, both with safety shut-off valve and safety relief valve. Such regulators are applied at the gas supply systems of residential and small-apartment houses as a part of household gas distributing plants.
5. Zero pressure regulator (DN 15÷150) - designed for proportional regulation of gas flow rate depending on rarefaction at the outlet or at the control point of pipeline, and maintenance of gas-air mixture in a constant ratio.
6. Gas-air pressure ratio regulator (DN 15÷150) - designed to obtain a gas-air mixture in the required ratio and automatically maintain this ratio.
CLIMATIC VERSIONS:
- -30…+60 °С
- -40…+60 °С
OPERATING MEDIUM TEMPERATURE:
- from -30 to +70 °С.
-------------------------------------
If you need help selecting necessary equipment, please visit our web-site www.termobrest.ru or contact our specialists by e-mail info@termobrest.ru or by phone:
+375 (162) 53-64-13 (technical consultation line);
+375 (162) 53-64-76 (sales and logistics department).
Блоки электромагнитных клапанов в угловом исполнении
Solenoid safety gas valves block unit in angle version is a set of solenoid safety gas valves and other gas fittings unit assembled into a single gas train (gas filter, pressure regulator-stabilizer, motorized gas valve, safety relief gas valve, safety shut-off gas valve, pressure switch, etc.).
In the units, the main safety valves and the gas filter are applied in an angle version.
Valve block units in angle version can be used at facilities where the circumstances are such that it would be difficult to assemble a linear block unit due to the face-to-face length. Furthermore, such units can be used in the process of design and development of measures aimed at restructuring of heat and power facilities, where the replacement of outdated gas train is required and the space is limited due to the existing gas pipeline supply, location of the boiler units and gas igniters.
TERMOBREST’s gas valve block units are suitable for any automated control system of boiler and burner equipment and can be used in the gas supply circuits for steam and hot water boilers of various types, including high-power boilers: PTVM, DKVR, DE and KVGM.
ADVANTAGES:
- Shorter face-to-face length of a gas train;
- Hydraulic resistance factor is 40% less compared with linear valve block units;
- A variety of standard models, with the possibility of developing individual solutions for specific projects;
- The use of TERMOBREST’s angle valve block units allow to significantly reduce the dimensions and consumption of gas pipeline valves of the burner, the number of welded joints, working hours for assembling and commissioning works, and to increase the operating reliability and length of service.
TECHNICAL SPECIFICATIONS for gas valve block units in angle version:
- DN 40…200, flanged connection;
- Рmax – 6 bar (0,6 МPа).
CLIMATIC VERSION:
- (-30…+60 °С);
- (-45…+60 °С);
- (-60…+60 °С);
- (-60…+60 °С);
AMBIENT TEMPERATURE:
- -60…+70°С;
- -45…+120 ˚С (special version);
- -45…+90 °С (special version – is indicated in structure).
POWER SOURCE, V:
- 220, 110, 24
AVERAGE LIFE:
- 20 YEARS
-------------------------------------
If you need help selecting necessary equipment, please visit our web-site www.termobrest.ru or contact our specialists by e-mail info@termobrest.ru or by phone:
+375 (162) 53-64-13 (technical consultation line);
+375 (162) 53-64-76 (sales and logistics department).